A thick glass door can be a decorative door with a new thickness of 12 mm or over. It is generally composed of two parts: the movable fan plus the fixed glass. The door frame is divided into metal, copper and aluminum metal. 1 Before the engineering is completed, check whether the elevation from the ground and the height belonging to the structure at the top from the door frame meet the theory requirements. Determine the position on the door frame and how you can install the wholesale Laminated Glass. Choose the glass in line with the design requirements. Concluded profile door frame, confine groove, plate and cup glue, floor spring, fire wood screw, self-tapping screw and also other auxiliary materials.
2 Installation points involving fixed door frame thicker glass (1) Release and positioning Reported by the design requirements, the position on the door frame is released, and the fixed and movable part installation manage lines are determined.
(2) The width on the stainless steel limit groove limit groove within the top of the installation door frame needs to be greater than the a glass thickness of 2~4mm, as well as groove depth is 10~20mm.
(3) Install the stainless veneer on the ground first, then glue the stainless steel panel to the timber side. The aluminum alloy square tube may be fixed on the frame column with an light weight aluminum corner code, or could be fixed on the embedded embedded portion by screws.
(4) Structure glass (usually pre-cut, then tempered and transported on the site for installation). The dimensions belonging to the bottom, middle and top with the actual volume should possibly be measured, and the cut size belonging to the minimum size of the glass width need to be selected. If the dimensions measured in the upper, middle and lower include the same, the size will be cut, the width is less than the measured size of 2-3 mm, and the height is less than Less than 6 mm. For the minimize glass, the chamfered edging is intended to be carried out on this four sides by hand-held oil-coated natural stone, with a chamfer bigger of 2 mm.
(5) Install the glass using a glass suction cup for you to lift the thick glass up, insert the thick glass plate into the limit groove at the superior of the door mode, and then place it on the bottom bracket so that this edge of the thicker glass plate just seals the side. The stainless steel trim belonging to the frame column faces your seam.
(6) The glass is fixed about the bottom bracket and that pressure clamp strip is actually installed, about 4mm from the thick glass menu. Then apply the universal glue within the strip and stick the stainless plate on the remove.
(7) Inject the glass seal to the top limit groove plus the bottom support, and inject the glass glue in to the joint between the thick glass along with the frame column, so that this glass glue forms some sort of uniform straight line along at the gap. Finally, scrape journey excess glass glue and wipe the glue using a clean cloth. When thicker glass is butted, the joint must be kept at a long distance of 2~3mm. The thick glass edge is required to be chamfered. After the two thick glass sit and fixed, the glass glue is employed to inject into this gap. After filling, the particular thick glass is stuffed. Squeeze the glass glue about both sides and wipe the glue which includes a clean cloth.
3 The installation point belonging to the movable door leaf thick glass The thick tumbler movable door leaf provides no door frame. The opening and closing belonging to the movable door leaf is realized through the hardware hinged to top of the and lower rails in the frame.
(1) Floor spring mounting ground spring is definitely an automatic door closing machine installed under various door fans.
(2) Mark top of the and lower rails from the door leaf, and fix the pin hole plate on the rotation pin and your rotation shaft connection plate on the floor spring by the wire. Refer to the installation instructions attached with the ground spring product for installation.
(3) Drill the holes inside the door handle (usually forced to be processed when paying for thick glass). Note how the height dimension of the actual thick glass should include the mounting portion that is inserted in to the upper and lower track. Usually the cut sizing of thick glass ought to be less than about 5mm with measurement size for realignment.
(4) Install the upper and lower rails on the upper and lower sides belonging to the thick glass door and also measure the height with the door. If the upper and lower edges in the door leaf are not the specified value inside gap between the door frame as well as the ground, the wooden splint is often placed under the glass within the upper and lower side rails. If the door leaf levels exceeds the installation width, the excess portion in the thick glass door leaf ought to be cut.
(5) After location the height, fix the upper and lower rails. At the gap between the thick glass as well as the metal upper and lower rails, a small wooden strip is inserted at the same time, and then the tumbler glue is injected in to the gap between the little wooden strip, the thick glass and also the crosspiece.
(6) Door supporter positioning installation. First, adjust the positioning pin to the door frame beam which consists of own adjustment screw towards the beam plane 1~2mm. Then erect the glass doorway leaf, align the hole position from the rotating pin connector on the lower crosspiece of the door leaf considering the rotation pin of the spring, and turn the door leaf to suit the hole into the actual pin. Then, with the pin axis because axis, turn the front door leaf 90° (to correct the door leaf whenever turning), so that the door leaf as well as door beam are during right angles. At this occassion, the hole of that rotating connecting piece from the crosspiece of the door leaf can be aligned on the front door frame beam. The positioning pin is ended up and the positioning pin is proved, and inserted into the hole from the door leaf cross-rotating pin connecting member is going 15 mm. Install the glass door handle. Previous to installation, apply a tiny amount of glass glue to the part where the handle is inserted into the glass. When the deal with is assembled, the root is closely along with the glass, and then the correcting screw is tightened to make certain the handle is certainly not loose.